Ghost Immobiliser Fitting
Guard your vehicle against key theft, cloning and hacking with the first aftermarket CAN-Immobiliser. The Ghost app and GPS tracking can be connected to the immobiliser to give you notifications when your vehicle is stolen or tampered with.
Installing an Ghost immobiliser is relatively straightforward for the qualified technician. Having the right tools, insulation tape and heat shrink tubing is essential.
Getting Started
Ghost immobilisers can be a great alternative to physical theft devices such as wheel locks and car alarms. They safeguard your vehicle without the use of LED indicators or key fobs. Instead, they connect directly to the ECU's CAN data network. They will only start by entering a PIN sequence. This gives a greater level of security against key hacking, ECU swapping and cloning.
Therefore, the installation of a ghost immobiliser Birmingham must be completed with a high degree of agility and accuracy. It can be a bit like navigating the minefield. A single mistake could cause irreparable damage to the circuits of the electrical system of your vehicle. It is crucial to know the installation procedure and prepare your vehicle properly.
First, you must prepare the vehicle by removing interior panels to make room for the immobiliser device. Once you have found the perfect place to hide it and you have it, use cable ties to fix it. Then, tidy up your wiring by making sure that loose wires are tied down and using insulation tape to cover the exposed connections. This will reduce the risk of a short circuit that is not intended to happen, while improving the aesthetics and reducing the chances of theft.
Find a source of constant 12V power and a grounding source for the ghost immobiliser. Once you've located them, test the power cables using a multimeter. Then, connect the CAN H and L wires from the immobiliser to your chosen power source and the grounding point.
It's important that you check all connections and examine the immobiliser for indications of corrosion. The process of entering a PIN and launching the vehicle is a great method to test the system. This should be part of your daily routine, as it will allow you to spot any issues that may arise early. Regular testing will also help to extend the life of the device and ensure that it is functioning at its best.
Preparing the vehicle
The installation of a Ghost immobiliser is a complex job that requires the appropriate tools and knowledge. A wiring diagram of the vehicle is crucial for locating the correct wires and establishing precise connections. A multimeter can help verify electrical values and ensure safety. Cable ties and insulation tape can be used to shield the connections from damage and keep them secured. A user's manual is provided for the Ghost Immobiliser. It will provide you with specific instructions tailored to that model.
Once installed the ghost immobiliser can stop engine starts that are not authorized by requiring the owner to input a unique code sequence using the buttons on the console or the steering wheel. The code can be altered at any time by the owner by hand or remotely using a mobile app. The device is also silent and is unnoticeable to thieves since it does not emit radio frequency.
Ghost immobilisers are directly connected to the CAN bus of the vehicle, a network that communicates with the electronic control units (ECUs) of the vehicle. It intercepts signals from the ECUs and stops the engine from running if the ECU detects a false signal. The system is weatherproof and tamperproof. It has no LED indicators or keys to draw thieves' attention.
It can be placed behind or in a more obscure area so that it's not easily spotted by thieves and does not interfere with vehicle's performance. It can be mounted in a small container so that it is less likely to be noticed by untrustworthy salespeople during a test drive.
Its stealthy operation, combined with its integration into the vehicle's CAN-bus system makes it an effective deterrent to vehicle theft techniques such as signal relay attacks and key cloning. The system can be paired with other security measures to create a formidable barrier that will frustrate even the most persistent thieves. This is why more insurance companies are suggesting or even requiring ghost immobilisers to be fitted, as it can significantly reduce the cost of insurance.
Making Connections
In contrast to traditional security systems that are heard by thieves ghost immobilisers work silently to prevent them from knowing when your vehicle has been switched on. They also stop the high-tech methods used to steal vehicles, like OBD port hacking. They can also be put in without causing permanent damage to your vehicle making them a good option for those who are planning to sell their car in the near future.
The Autowatch Ghost 2 CANbus immobiliser is among the most recent and most reliable solutions to stop car theft. It utilizes the CAN data network to disable your engine and generates a PIN code that only you know, which means it is difficult for thieves to identify. It can be used on a wide range of vehicles, and it works with many features already installed, such as car alarms and steering wheel locks. GPS trackers and door lock bypass.
If you decide to go with a Ghost immobiliser, be sure to consult the wiring diagram for your specific vehicle model to determine the wires that need connecting. Verify their positions to ensure they are correct, and then label them or tape them to help you remember them. You will also need to find a source of constant power (12V) and a grounding point to the system. Once you have these in place, you can start to make the connections needed to complete the installation.
The ghost immobiliser will not allow your vehicle to start until the pin code is entered through the buttons on the dashboard or steering wheel. This will stop ECU hacking keys cloning, hacking, and other techniques of theft from vehicles. Additionally, it can be combined with other Thatcham-approved security accessories, such as alarms and tyre clamps to provide your vehicle with an even greater level of protection.
As the UK automotive industry continues to grow so do the options available for protecting your vehicle. There are a myriad of ways for thieves to gain access into your car and steal it, which is why it's crucial to take every precaution to ensure that it isn't taken. ghost immobiliser tracker have become an increasingly popular option for car owners who are responsible.
Testing the System
The Ghost Immobiliser uses a CAN data network to communicate with the vehicle's ECU which stops the engine from running until a specific PIN code is entered. This makes it difficult for thieves to steal your key fob to start your vehicle, and even harder to disable the system through hacking its electronic.
Ghost Immobilisers are also able to be used in conjunction with GPS tracking devices that will aid in tracking your vehicle and track it in the event of theft. This isn't an option that is commonly used in aftermarket security solutions, but it's a great method to enhance your security and get peace of mind knowing that your vehicle is always protected.
The Ghost-II immobiliser not only provides an enhanced security, but also a pleasant experience for the user by getting rid of the need for additional key fobs or devices. It features an easy and intuitive PIN code entry system that integrates seamlessly into your daily routine. It also offers convenience features and deactivation settings that allow you to temporarily disable the immobiliser so that you can park or service your vehicle.
Before beginning the installation process, you should familiarize yourself with the vehicle's wiring and prepare the necessary tools. A basic set of tools will allow you to create precise connections. A multimeter is a tool to test electrical values. Insulation tape and heat shrink tubing are also crucial to protect connections from short circuits and cable ties can be used to keep the wiring in the correct position. Additionally, it is essential to work in a well-lit location and wear appropriate safety gear when working with electrical tools and components.
After you've completed the installation, you must test the Ghost immobiliser to make sure that it's working properly. First, you should try to start the vehicle without entering the PIN code. If this fails, you'll have to retest the system and conduct a more thorough examination of the connections.
In contrast to other security systems that are available, the Ghost Immobiliser is a covert device that cannot be detected by thieves and is far more effective than conventional physical deterrents, such as wheel clamps or steering locks. It is TASSA acknowledged and approved by a few insurance companies, making it an investment that is cost-effective and will provide you with the peace of mind you deserve.